| ATEX Products |
 |
| Des têtes bien faites... |
|
|
|
| BAMOPHOX 436, Turbidity monitor |
General Catalogue 436-01 |
BAMOPHOX 436
|
|
BAMOPHOX 436, Turbidity monitor
- Alphanumeric back lighted LCD display
- 2 models available:
Panel mounting 72 x 144 (436E)
Wall mounting IP 65 (436M)
- 3 relay outputs (Normally Open contacts)
- 1 relay output for system alarm
- 2 analogical outputs 0/4-20mA
- Scales
NTU, FAU, mg/L, g/L, FNU
From 0.000 to 9999
- OPTIONS:
RS 422 /J-BUS + LOGGER (MMC card)
Extension for a 2nd measurement input, displayed values on the lower line) |
An extension terminal (wall, panel mounting or DIN rail mounting):
- Allows a second measurement parameter (pH, Conductivity, Chlorine,dissolved Oxygen, Turbidity, Flow, and any 4-20 mA, depending of themodel)
- Data from this blind BAMOPHOX are displayed on the main device(on the second line display).
- A 4 wires shielded cable is necessary to link both instruments (maximum length of 500 m)
- The options RS422 and the data logger are shared between bothBAMOPHOX.
- Rail DIN mounting instrument (436 D/A). |
| The BAMOPHOX 436 offers high flexibility on use mixing different built-inprogrammes for regulation, thresholds, temperature compensation, andalarms. The 2 lines back lighted display, 16 alphanumerical characters, givesan easy measurement and temperature reading in any conditions. It alsodisplays the configuration menu and settings of thresholds, analogicaloutputs, operation data modes. To allow a quick and easy diagnostic afterconfiguration a simulation program is built-in with direct actuation oncontacts outputs, and analogical outputs. A copy of the signal on the 4-20mA output is galvanic insulated; it can be set up within all scales of theparameter. Temperature measurement is also available on a 4-20 mA. |
Displayed parameters: Measurement values of Turbidity - Configuration Menu - Temperature value
Display: Back lighted - 2 lines of 16 alphanumerical characters ; 9,2 mm highIndication: LED alarms status
Configuration: 8 push buttons keyboard on front face - Keyword protected
Units: NTU, FAU, mg/L, g/L, FNU
ScaleSet up from 0.001 to 9999, adjustable decimal point
Turbidity measurement: input 0/4-20 mA
Temperature: input for a 3 wires Pt 100 Ohm/0°C
Relay outputs: 4 closing contacts (Silver alloy), voltage free
3 programmable independent thresholds - with adjustable hysteresis 0…100% - and adjustable timer from 0 to 9999 sec
1 Output relay (S4) as a common alarm for:- open loop- Pt 100 Ohm dysfunction
Contact: Switching capacity 250 V / 3A AC, 30 V / 3A DC, minimum 100 mA / 5 V DC
Measurement output: 0/4-20 mA (maxi 600 Ohm) proportional to measurement, galvanic insulated
Temperature output: 0/4-20 mA (max 600 Ohm), scaling 0…100°C, galvanic insulated
Main power supply: 230 V AC / 50-60 Hz [other on request] - Consumption 10 VA
Models: Panel mounting, front IP65, 72 x 144 mm, connections on screw terminal IP40Idem DIN Rail mounting, only for blind monitor, IP40 Wall mounting, IP65, cable glands, connections on screw terminal
OPTION (RS 422 + Logger)
Communication: RS422 output, J-BUS link, binary slave mode, 2400 to 9600 bauds
Data Logger: Cycle average measurement record, with a programmable period, 150000 records on MMC(multimedia card) / External driver necessary for reading
CE labellabelized CE in conformity with 73/23/CEE low power and electromagnetic compatibilty 89/336/CEE |
|
 |
Turbidity monitor
BAMOPHOX 436 |
General Catalogue
436-01 |
|
|